STROBO Gralmarine, 3600lm, Diving Torch, Diving Flashlight, Divers Signalisation

Description

STROBO Gralmarine, 3600lm
Power: 30 W
Light quantity: 3 600 lum
Focusing angle: 270°
Dimensions: Ø 40 / 125 mm
Weight: 0,25 kg
Power supply: 1 x 18650 Li-ion, possibe use of 26650 battery
Burn time in normal mode: 10 hours
Works in two modes:
normal: 5 flashes - 1 second break - another 5 flashes, mode works between 4,2 V – 3,6 V (charged battery)
economical (switches automatically): 2 flashes – 2,5 seconds break – another 2 flashes, mode works below 3,6 V (strong discharged battery)
Possible individual engraving - name on the torch
Rechargeable 18650 battery, charger and clip for fastening in set
Pressure tested to 150 m, 300 m on request
This set comprises of:
• LED torch
• Li-ION battery type 18650 capacity 2,8 Ah
• battery charger
STROBO TORCH:
➢ was created as a marker of the line or exit point from a diving place
➢ construction:
• torch body is built of a surface anodized aluminum
• torch head made of high-resistant transparent material and a surface anodized aluminum
• torch is switched on / off by tightening / loosening the head with one turn (avoid excessive loosening of the head under water)
• battery is placed inside of the torch with the positive terminal (+) on top, any other battery insertion will not activate the torch
➢ the source of light are three Cree XML-2 diodes, with a color temperature of 5500 – 6000 K
➢ requires battery type 18650 or 26650 power supply, with nominal voltage of 3,7 V, the use of other batteries can damage the head
(LED burnout)
➢ works in two modes:
• normal: 5 flashes - 1 second break - another 5 flashes, mode works between 4,2 V – 3,6 V (charged battery)
• economical (switches automatically): 2 flashes – 2,5 seconds break – another 2 flashes, mode works below 3,6 V (strong
discharged battery)
• the torch switches off below 3 V (fully discharged battery)
➢ tested to a depth of 150 meters, 300 meters on request
➢ Preparation of the torch for diving:
• check the proper working of the torch before diving
• check if the battery is in a good condition
• check the o-rings for dirt and damage
➢ Maintenance of the torch after diving:
• rinse the torch with fresh water
• dry
• remove dirt regularly
• wipe the front surface of the head with a soft, moist cloth; do not use alcohol-based detergents (these cause dulling and cracking of
the transparent material)
• periodically check the condition of the o-rings, replace when worn or damaged (size of the o-rings on the torch body: 28 x 2,5)
• periodically check the condition of the thread, lubricate with silicone grease or silicone with Teflon - this eases the torch’s operation
and reduces stress on the o-rings
• periodically open the torch with the aim of releasing the accumulated gas –batteries release a gas, which may lead to possible
damage by increasing pressure inside of the torch and pushing window out, remove the battery while the torch is longer stored
• care for mechanical damage, distortions to the torch head may cause leaks
➢ Charging the battery:
• unscrew the torch head
• remove the battery
• place the battery into the charger, according to the marked polarity, use only chargers for charging single-cell Li-ION batteries
• connect the charger to the 110 – 230 V power source
• the level of battery charge is indicated by the LED color (red indicates “charging”, green indicates “charged”)
➢ Warnings:
➢ do not use a different power source other than battery type 18650 or 26650, with nominal voltage of 3,7 V
➢ do not disassemble the torch
➢ do not throw the torch or expose for strong vibrations
➢ do not immerse in water or dive with a loose torch head or with an open torch
➢ do not expose the torch to high temperatures (above 50° C)
IN OUR OFFER YOU CAN FIND ALL PRODUCTS OF GRALMARINE DIVING LIGHTS. CONTACT US FOR MORE DETAILS.